ATTENTION: All Postings that advertise items for sale will be deleted from the Discussion Forum. You may post sale items for free in the Classifieds section. Sign up now.
Hi,
We need to replace our Comfort Control Center part # 3106463.007 with the replacement part # 3310009000. One is 4 button and the replacement is 5 button. Do they interchange easily or does it require any rewiring between the Control Center and the A/C units?
Thanks,
M.Moore
My Duo-Therm comfort control center will not work the rear ac unit. It also jumps around when trying to change the mode. I would be interested in purchasing a rebuilt unit.
Thanks Chris
I have a well functioning 3 unit (620315) A/C system in my bus conversion being controled by one 4 button 3106463.007 Comfort control Center, which does support 4 zones.
I wish to add a 4th A/C unit. Is it possible to obtain a working (possibly rebuit) control board which I could install into a new (600315 or 620526) A/C unit so that it could communicate with and be controled by my existing system?
Thanks for your help!
I can sell you a rebuilt and tested 4 button board for $80.00 exchange if the ON-OFF switch is OK. $20.00 additional if the switch is bad. Let me know if this would help. BH
I have a 4 button duotherm thermostate with a bad off/on switch. Do you know where I can purchase a new or rebuilt one. I have already check on the conversion from a 4 to 5 button and is a little expensive. Thanks
I have a 5 button thermostat in my coach...the on/off does not work, dial does not light up either....can't locate a number on it but the number on the board is 50-981501-8. like some information as to if the board is possibly bad...travlondwn@aol.com
I have a 4 button comfort control center Part no 3106463.007. You have to hit the buttons several times to get it work. The on and off button works fine. Any help would be appreciate. Martin S. Jenkins 910-391-5878
I to have a Comfort Control Duo-Therm 3106463.007 that you have to push the up button numerous time to increase the temperature. Sounds as this this is a common problem among this particular PCB. What is the solution?
I have the 4 button 2 AC model. The OFF/ON is okay but the MODE switch is faulty. Would the person that rebuids them please respond.
dolldave@embarqmail.com
Do I understand that I can purhase a rebuilt 4 button controller? I, too, am having trouble with mine and don't quite know what to do. I would appreciate any help you could give me. My on-off switch works fine... my problem is that the controller seems to lock up at times with furnace mode refusing to go off. This then keeps the air cond. from working ar all. HELP! Thanks-Richard
Do you still have rebuilt boards available? I have two duo therm 59530.601 units with 3106481.009 boards
(with a 4 button control unit). The front board is burned out - when front unit is started we get an electical smell from board. I can also see evidence of a waxxy substance at the base of a few components on the board. There was a problem with our electical supply that caused this initially. Rear unit seems to work OK except it doesn't always shut off at set temp.
I need a replacement 316463.007 I purchased a five button on the enternet by mistake and now am stuck with it. what can I do? i am willing to purchase a rebuilt or after market model please help my mother lives in it.
He mr. hendrix, would i be able to get your phone number so i can call you to get a couple questions answered?- i am in need of a comfort comtrol p/n 3106463.007. thanks!!! tj
I have said unit....is not reponding to Zone changes... not heat or cool sensative seems to be about 8 to 10 degrees off? mostly I would like to be able to use zone change buttons without going out of my mind. Also if I use on off button? it may or may not ever come back? scary
regards
George
I have lost the instructions to hooking up thermostat could you please tell me what wires are for the furnace
thank you for any information you could give me
I recently bought an Endeavor Rv. The stat is Duo-therm confort control w/4 buttons. It work on furnace mode but don't stop at desire temperature. Is there a procedure to program this stat? Thanks
Loks like Duo-Therm has some real issues with their four button Comfort Control. Mine was like all of yours and i had read an article in FMCA, I believe their July or August 2007 issue, where you could take the unit apart and carefully re-bend the brass contact under the push button so they would once again make contact. I tried but did not bend properly and made it worse. Can you buy just the brass bars? I am now proficient in the R&R of the unit after many attempts to properly bend the contact.
I would like to replace my dometic control center with either a new or rebuilt part # 3106463.007. Mine works fine but it is difficult to change zones. can you help me. Thanks
Doeeds the cleaning help.i have 2 zones can't get zone 1 fan to speed up very slow to get anything to get going.would be interested in buying rebuild.thanks
email M.Moore
reply to message
post new message
search forums
